Biomass moisture-control unit for the world's largest HTL plant for biomass

Arbios Biotech - Prince George, Canada
Sector: Renewable fuels – hydrothermal liquefaction (HTL)
Challenge: Achieving consistent feedstock moisture despite highly variable material properties and high fines content
Solution: a modular BT belt dryer using excess HTL process heat, combined with a self-cleaning filter belt system, to reliably achieve consistent feedstock moisture levels
Dryer used: Belt dryer type BT 1/6200-12
Product to be dried: Residual wood from sawmill residues (bark, wood chips, shavings)
Challenge
To ensure the HTL process can operate stably and with maximum yield, the feedstock, predominantly sawmill residues such as bark and wood chips with varying mixtures of green biomass such as residues from forest harvesting, had to be moisture controlled to a consistent moisture level. Three requirements were decisive for the design of the drying system and the project execution:
- The highly fluctuating particle size distribution and composition of the feedstock
- The high proportion of fines in the material, which leads to deposits on the belt and increased dust load in the exhaust air without suitable filter and cleaning technology
- The close project coordination between Australia, Canada, and Germany across twelve time zones
Solution
STELA supplied a belt dryer from the proven BT series in a fresh air/exhaust air configuration (type BT 1/6200-12) for pre-drying the input material. The system operates with a throughput capacity of up to 80 m³/h and achieves a drying capacity of approximately 4.5 t/h of dry product at a target moisture level of less than 30%, with an evaporation capacity of up to 3.5 t of water/h. The annual average heat demand is approximately 4 MW; this is covered by excess process heat from the HTL process itself, which significantly increases the efficiency of the system.
To address the high proportion of fines and the fluctuating particle size distribution, the dryer is equipped with a filter belt that is continuously cleaned wet and dry, thus ensuring reliable continuous operation without manual cleaning downtimes. The compact, modular design of the BT series, which has already been installed more than 400 times worldwide, enabled a highly scalable, field-proven solution without the need for a facility-specific new development.

Performance Data
The STELA belt dryer type BT 1/6200-12 at Arbios is designed for the following data:
Throughput capacity: up to 80 Thm³/h
Drying capacity: approx. 4.5 t/h dry product at less than 30% residual moisture
Evaporation capacity: up to 3.5 t water/h
Heat demand: approx. 4 MW on annual average, predominantly from excess HTL process heat
Year of commissioning: 2022
Conclusion and outlook
Since commissioning, the moisture control system has been reliably supplying pre-dried material for the world's largest biomass HTL plant. By utilizing excess process heat from the HTL process, the drying system operates with comparatively low additional energy requirements, while the continuous belt filter cleaning ensures stable continuous operation even with a high proportion of fines in the feedstock.
About Arbios Biotech
Arbios Biotech (Arbios) transforms underutilized biomass into a renewable bio-oil that can be further refined into sustainable transportation fuels and chemicals with a low carbon footprint. Utilizing their parent company Licella’s patented Cat-HTR™ platform, Arbios enables an efficient pathway for transforming waste streams into high-value low-carbon solutions. At the Chuntoh-Ghuna facility in Prince George, British Columbia, Arbios operates the world's largest biomass based hydrothermal liquefaction facility, converting forest residues and sawmill residues into a high-quality, renewable bio-oil. Designed for approximately 50,000 barrels of bio-oil per year from about 25,000 tons of dry wood residues, the facility began commissioning at the end of 2024, with the moisture control unit pre-commissioned at the end of installation, in 2022.

Downloads
Find out more about the belt drying system type BT:
Get in contact

Контактное лицо
Низкотемпературная сушилка или сушилка непрерывного либо циклического действия — вы не знаете, что вам подойдет лучше всего? Наши опытные специалисты будут рады помочь вам найти лучшее решение для вашего продукта. Не стесняйтесь обращаться к нам за консультацией без каких-либо обязательств.
Телефон: +49 8724 899-10
Эл. почта: sales[at]stela.de
