Стрічкова сушарка тип BT

STELA belt dryers type BT are separated in three levels

At the top, ambient air is fed through heating coils in the fresh air intake and thus heated. Depending on the local conditions, thermal oil, saturated steam, waste heat from combined heat and power and ORC processes or already heated process air can be used flexibly as heating media. By several dryer zones arranged in a row at this upper level it is possible to create drying areas with different process temperatures.

The dry material is evenly applied to the drying belt running underneath, which is made of an air-permeable, woven plastic material, via a double distribution screw. The warm air from the heating above is sucked down through this dryer belt, removing the moisture from the material on the belt.

In the extract air area below the belt, the moisture-saturated extract air is released into the environment.

Belt dryer made to measure

Belt widths depend on the required water evaporation and can vary between 2 and 8.4 m, depending on the application Thanks to their enclosed design, they are also suitable for cold regions with outside temperatures down to -40° C. The capacity of the belt dryers is designed according to demand and is largely defined by the amount of water that the dryer is to extract from the material per hour. The systems are designed for capacities of 200 kg to 60 t of water per hour.

Air ducting

Air can flow through the process belts from above as well as from below. The belts can be zoned via the belt length. Several belts can be ventilated one after the other via the same air flow.

The dryers are available both as exhaust air and recirculation systems. Optionally, exhaust air heat recovery can also be implemented.

Додаткова інформація

Тут ви можете завантажити брошури, які містять інформацію про низькотемпературні стрічкові сушарки. З них Ви дізнаєтесь про всі можливі опції, види, їх характеристики і принцип роботи, щоб краще зрозуміти що підходить саме для вашого виробництва і продукту.

• Nizkotemperaturna_strichkova_susharka_ukr.pdf4 MB

Belt dryer BTL for sawdust
in Austria

Dryer type: BTL 1-3000-27
Dryer output capacity:
sawdust: 5.0 t/h from 50% to 10%

Belt dryer BT for sawdust
in Austria

Dryer type: BT 1-6200-16.5
Dryer output capacity:
sawdust: 6.7 t/h from 45% to 10%

Belt dryer BTL for sawdust
in Ukraine

Dryer type: BTL 1-3000-9
Dryer output capacity:
sawdust: 1.5 t/h from 45% to 10%

Belt Dryer BTU for sawdust
in Lithuania

Dryer type: BTU 1-6200-36-4-4
Dryer output capacity:
sawdust: 20.5 t/h from 45% to 8%

Belt dryer RecuDry® for wood chips and sawdust
in Lithuania

Dryer type: BTU RecuDry 1-6200-34.5
Dryer output capacity:
wood chips and sawdust: 14.0 t/h from 47% to 2%

Belt dryer BT for sawdust
in Argentina

Dryer type: BT 1-6200-9
Dryer output capacity:
sawdust: 3.0 t/h from 50% to 11%

Belt dryer BT for wood chips G30
in Germany

Dryer type: BT 1-6200-12
Dryer output capacity:
wood chips G30: 5.6 t/h from 50% to 20%

Belt dryer BTL for waste
in France

Dryer type: BTL 1-3000-20
Dryer output capacity:
waste: 3.0 t/h from 45% to 8%

Belt dryer BT for hog-fuel
in Canada

Dryer type: BT 1-6200-12
Dryer output capacity:
hog-fuel: 4.5 t/h from 55% to 20%

To the references To the case studies

Зв'яжіться з нами

Контактні особи

Який тип сушарки обрати? З модулем рециркуляції чи з модулем конденсації? Якщо ви не впевнені, яка сушарка відповідає вашим потребам - наші досвічені колеги з радістю допоможуть знайти найкраще рішення для вашого продукту. Ми працюємо для вас, тому звертайтесь до нас за консультацією без будь-яких вагань.

Телефон +49 8724 899-10
Ел. пошта